Product: Pligun 90

Product #: 3334

Service Temperature Limit: 3300°F

Installation Method:  Gunning

Shelf Life:  9 months

Industries:  Oil/Gas, Off-Gas, Chemical-Ammonia, Steel, Ferrous, Refining, Pulp & Paper, Thermal Oxidizers

Best Applications:  Designed for very high temperature and/or reducing atmosphere applications in industrial processes, including:

  1. Thermal Oxidizer burner and reducing zones
  2. Ammonia Reformers
  3. Oil fired and waste heat boilers
  4. Carbon Black Reactors
  5. Sulfur recovery units

Plibrico TDS Link – https://plibri.co/3WCE9B7

Product Information: Pligun® 90 is a high alumina, high strength, conventional gun mix for service at elevated temperatures and demanding conditions.   It provides excellent chemical resistance as well as good abrasion resistance.   Pligun 90 has a low silica content making it suitable for high-temperature hydrogen atmospheres.   This gun mix utilizes a high purity corundum aggregate and matrix, bonded by high purity calcium aluminate cement.   It can be used in a variety of applications where a high purity refractory is required.   Further product advantages for Pligun 90 include:

  • Good physical properties for a conventional gun mix at elevated temperatures above 2000°F
  • Excellent resistance to reducing and hydrogen atmospheres
  • High Refractoriness
  • Good high temperature creep resistance
  • High thermal expansion coefficient
  • High thermal conductivity
  • Good gunability

Available Internationally As:  Plico® Gun Mix 90

Plibrico SDS Link – https://plibri.co/3SHVlE6

Product: Redline Red Hot G 45

Product #: 52408

 

Service Temperature Limit:   2700oF

Installation Method:  Gunning

Shelf Life: 9 months

 

Industries: Power Generation, Off-Gas, Heat Treat, Foundry, Incineration, Boilers

Best Applications: This material is engineered for resurfacing existing refractory surfaces while still in a “hot” condition, these include:

  1. Soaking Pits
  2. Common Tunnels
  3. Dryers and calciners
  4. Heat Treat Furnaces
  5. Incinerators / Thermal Oxidizers

Plibrico TDS Link – https://plibri.co/4c5kOyV

Product Information:  Redline™ Red Hot G 45 is a 45% alumina, flint based low cement gun mix designed for resurfacing existing refractory surfaces.   It is generally applied in hot conditions, but can also be used cold.  Red Hot G 45 is typically used as a hot or cold service/repair material but can be used as a primary lining.  Product advantages include:

  • Excellent for hot gunning installations
  • Low rebound
  • Good adherence to old refractory
  • No special gunning installation requirements
  • Economical

 

Available Internationally As: Redline Red Hot G 45

Plibrico SDS Link – https://plibri.co/4b5NWVE

 

Product: Redline Redgun 45ES

Product #: 52302

Service Temperature Limit:  2500°F

Shelf Life: 12 months

Product Information: Redline Redgun 45ES is a first quality gunning mix that exhibits excellent strengths combined with good resistance to abrasion and mechanical abuse.   It is a general purpose mix that has many applications.   Common applications include marine and stationary boilers, ashpits, and cement clinker coolers.

Product: Redline Red Hot G 60/5

Product #: 52304

Service Temperature Limit:

Aluminum Contact –  1700°F

Non-Contact – 3100°F

Shelf Life: 9 months

Product Information: Redline™ Red Hot G 60/5 is a mullite based gun designed for resurfacing existing refractory surfaces.   It contains a silicon carbide addition to help resist corundum build up.   It is generally applied in hot conditions, but can also be used cold.   This material contains a non-wetting system and can be used above and below metal line in aluminum processing furnaces.

Product: Redline Red Hot G 70/5

Product #: 52305

Service Temperature Limit:

Aluminum Contact –  1700°F

Non-Contact – 3100°F

Shelf Life: 9 months

Product Information: Redline™ Red Hot G 70/5 is a mullite based gunning mix which can be applied either hot or cold.   It contains a silicon carbide addition to help resist corundum buildup.   This material develops an excellent bond with existing refractory surfaces and was designed to be applied over worn linings in aluminum processing furnaces.   It contains a non-wetting system and be applied both above and below the metal line.

Product: Pligun Tuff Mix
Product #: 14033

Service Temperature Limit: 2500°F

Installation Method: Gunning
Shelf Life: 12 months

Industries: Mineral Processing, Aluminum, Steel, Power Generation, Boilers, Incineration, Off-Gas, Foundry, Ethanol

Best Applications: Typical thermal applications include:

  1. Wet Bottom Ash Hoppers
  2. Incinerators
  3. Boilers
  4. Dryers and Calciners
  5. Stacks

Plibrico TDS Linkhttp://bit.ly/31pnFOB

Product Information: Pligun®️ Tuff Mix is a Plibrico Company “go to” gunning mix for general refractory use up to 2500°F. Possessing moderate density, good strength, as well as excellent gunning characteristics, it has applications across many of the major thermal industries. This “Tuff” material, when gunned properly, produces rugged refractory linings with good volume stability. Product advantages include:

  • Good strength to density ratio for economical use
  • Moderate thermal expansion
  • Moderate thermal conductivity
  • Low rebound and gunning water range
  • No special gunning installation requirements

Available Internationally As: Plico®️ Gun Mix Tuff Mix

Plibrico SDS Linkhttp://bit.ly/2Kjx6JL

Product: Pligun Super Tuff Mix
Product #: 14150

Service Temperature Limit: 2600°F

Installation Method: Gunning
Shelf Life: 12 months

Industries: Power Generation, Incineration, Off-Gas, Boilers, Steel, Aluminum/Non-Ferrous

Best Applications: This material works wonderful in applications such as:

  1. Atmosphere heat treat furnaces
  2. Wet Bottom ash hoppers
  3. Incinerators and thermal oxidizers
  4. Boilers
  5. Dryers and calciners
  6. Stacks

Plibrico TDS Linkhttp://bit.ly/2QwVf2O

Product Information: Pligun™️ Super Tuff Mix is a lower iron content version of Pligun™️ Tuff Mix. While possessing most the attributes, the low iron content of the bonding matrix increases the service limit of Pligun Super Tuff Mix to 2600°F, and also makes it suitable for use in moderate reducing atmosphere environments. This general use gunning mix has moderate density, good strength as well as excellent gunning characteristics. Product advantages include:

  • Good strength to density ratio
  • Moderate thermal expansion
  • Moderate thermal conductivity
  • Low iron content for reducing atmospheres
  • Low rebound and gunning water range
  • No special gunning installation requirements

Available Internationally As: Plico®️ Gun Mix Super Tuff Mix

Plibrico SDS Linkhttp://bit.ly/2On59Bw

Service Temperature Limit

2700°F

Installation Method

Gunning

Shelf Life

9 months

Industries

Waste-to-Energy, Incineration, Boilers

Best Applications

Operations that require high refractory thermal conductivity, including:

  1. Initial Installation
    • Water wall studded tube protection in waste incinerators
    • Water wall studded tube protection in boilers
  2. Gunning Maintenance
    • Water wall studded tube protection in waste incinerators
    • Water wall studded tube protection in boilers
  3. Any other application requiring a high conductivity refractory

Product Information

Pligun® SiC HP8 is an 80% silicon carbide, high performance gun mix.   This product was developed to meet the demanding specifications for waste incineration boiler tube sheet refractory.   Independently evaluated against other competitive materials, Pligun SiC HP8 achieved and excelled in many areas including:

  • High mechanical strength – both hot and cold
  • High thermal conductivity
  • Relatively low abrasion loss
  • Resistance to acid slag corrosion
  • Good gunability and low rebound

Service Temperature Limit

2700oF

Installation Method

Gunning, Hand Packing, Troweling

Shelf Life

9 months

Industries

Power Generation, Waste to Energy, Incineration, Boilers

Best Applications

Initial installation and gunning maintenance for:

  1. Water wall studded tube protection in waste incinerators and boilers
  2. Applications requiring a high conductivity refractory

Product Information

Pligun SiC 80 TM is an 80% silicon carbide gun mix.   This versatile product exhibits good gunning characteristics and is also designed for micro applications.   You can apply via hand packing or troweling for small applications and tight areas like behind boiler tubes and studs.   Pligun SiC 80 TM product advantages include:

  • Good mechanical strength
  • High thermal conductivity
  • Resistance to acid slag corrosion

Product: Pligun 70 KK

Product #: 13023

Service Temperature Limit: 3100°F

Installation Method: Gunning

Shelf Life: 6 months

Industries: Steel, Aluminum, Boilers, Incineration

Best Applications: Super for both repair and resurfacing of worn refractory as well as for new installations. Typical applications include:

  1. Reheat, forging, and heat treat furnaces – walls and roofs
  2. Aluminum furnaces (non-metal contact areas)
  3. Incinerators and thermal oxidizers
  4. Boilers and heaters
  5. Dryers and calciners
  6. Stacks and ducts

Plibrico TDS Linkhttps://plibri.co/2Tg8Mwo

Product Information: Pligun® 70 KK is a 70% alumina conventional gunning mix for use in applications up to 3100°F. The gunning material has a high mullite content, possesses excellent gunning characteristics, and requires no special gunning procedures. Product advantages include:

  • Good strength: hot and cold
  • Moderate density
  • Reheat volume stability
  • Moderate thermal expansion and conductivity
  • Good adherence to worn refractory
  • Low rebound and gunning water range
  • No special gunning installation requirements
  • Available Internationally As: Plico® Gun Mix 70 KK

Plibrico SDS Linkhttps://plibri.co/3cUiVGZ

  • Plibrico® Plastic Refractories

    Clay/Air Bond

    Product Name%Al2O3Service LimitSDS
    Plibrico®Super F AB58%2900F / 1590CSDS
    Plibrico®60 AB58%3100F / 1705CSDS
    Plibrico®80 AB78%3200F / 1760CSDS
    Plibrico®90 AB90%3400F / 1871CSDS

    Phosphate Bond

    Product Name%Al2O3Service LimitSDS
    Plibrico®55 S54%3000F / 1648CSDS
    Plibrico®68 S68%3100F / 1705CSDS
    Plibrico®68 SA68%3100F / 1705CSDS
    Plibrico®85 S Special83%3300F / 1815CSDS
    Plibrico®90 S90%3400F / 1870CSDS
    Plibrico®SiC 80(80% SiC)2700F / 1480CSDS

    (fine grain – soft)

    Product Name%Al2O3Service LimitSDS
    Plibrico®SR 6868%3100F / 1705CSDS
    Plibrico®SR 8583%3300F / 1815CSDS
    Plibrico®SR 9088%3400F / 1870CSDS

    Plibrico HyRATE® Plastic Refractories – Gunning Grade

    Clay/Air Bond

    Product Name%Al2O3Service LimitSDS
    Plibrico HyRATE®Super F AB43%2900F / 1595CSDS
    Plibrico HyRATE®60 AB60%3100F / 1705CSDS
    Plibrico HyRATE®80 AB78%3200F / 1760CSDS

    Phosphate Bond

    Product Name%Al2O3Service LimitSDS
    Plibrico HyRATE®68 S68%3100F / 1705CSDS
    Plibrico HyRATE®85 S Special84%3300F / 1815CSDS