Product: Plicast LWI 24 QS

Product #: 3330

 Service Temperature Limit: 2450°F

 Installation Method:  Casting

Shelf Life:  12 months

 Industries:  Aluminum, Mineral Processing, Power Generation, Boilers, Incineration, Off Gas, Thermal Oxidizers

Best Applications:  Engineered for applications requiring a high temperature insulating component, these include:

1. Reheat, car bottom and annealing furnaces – backup insulation
2. Boilers
3. Incinerators and thermal oxidizers
4. Aluminum furnaces – upper wall and backup insulation
5. Mineral processing kilns – backup insulation
6. Fired process heaters
7. Dryers

Plibrico TDS Link – https://plibri.co/3xutZcF

Product Information: Plicast® LWI® 24 QS is a quick setting insulating refractory castable.   A service limit of 2450°F, moderate density, and adequate strength, make this material suitable for use as either as an efficient backup insulating component, or a primary lining material in less demanding, moderate temperature applications.   Product advantages include:

• Quick Setting
• Good strength
• 2450°F service limit
• Medium density ~80 pcf
• Moderately low thermal conductivity
• Good volume stability
• Good casting consistency
• Good product storage life: 12 mth

Available Internationally As:  Plico® Castable LW 24 QS

 Plibrico SDS Link – https://plibri.co/3THObzj

Product: Plicast Airlite 25 C/G

Product #: 3271

Service Temperature Limit:  2500°F

Installation Method:  Gunning, Casting, Troweling

Shelf Life:  6 months

Industries:  Boilers, Thermal Oxidizers, Steel, Petrochemical, Aluminum, Mineral Processing

Best Applications:  Engineered as a “Liquid Board™”… this highly insulating backup lining can be used as a replacement option for block insulation where cutting and fitting ceramic fiber board and block insulations are impractical or not economical.   Typical applications include:

1. Boilers where block insulation is used
2. Fired heaters – backup insulation
3. Incinerators and thermal oxidizers – backup insulation
4. Aluminum furnaces – backup insulation
5. Reheat furnaces – backup insulation
6. Homogenizing furnaces

Plibrico TDS Link – https://plibri.co/2Y0VFAy

Product Information: Plicast® Airlite 25 C/G is a low-density insulating mix which can be gunned, poured, or troweled into place.   This Liquid Board™ type of material has the versatility needed for ceramic fiber board/block insulation applications that require a significant amount of cutting and fitting around complex geometries or anchors.   Because of its low thermal conductivity, it has very similar insulating properties to block insulation.   For use as a backup lining only and not a working lining.   Product advantages include:

• Low density
• Low thermal conductivity
• Versatility and ease of installation
• Low rebound

Available Internationally As:  Plico Castable Airlite 25 C/G

Plibrico SDS Link – https://plibri.co/3pcifnf

Product: Plicast LWI 24 HS

Product #: 3263

Service Temperature Limit: 2400°F

Installation Method:  Casting

Shelf Life:  6 months

Industries:  Aluminum, Steel, Petrochemical, Incineration, Boiler

Best Applications:  This lightweight material with exceptionally high strength, and its aluminum resistant version (Plicast Al-Tuff LWI 24 HS), is recommended for applications that include:

1. Precast Shapes where weight is a factor
2. Linings for reheat furnace floors
3. Annealing furnace cartops
4. Fired oil heater stacks
5. Carbon monoxide boiler duct linings
6. Olefins cracking furnace stacks
7. Over-the-road aluminum ladles
8. Backup linings in aluminum furnaces

Plibrico TDS Link – https://plibri.co/2XkWYLJ

Product Information: Plicast® LWI® 24 HS is an insulating castable that is based on a light weight alumino-silicate aggregate system.   This lightweight material and its Al-Tuff aluminum resistant version (Plicast Al-Tuff LWI 24 HS), possess exceptionally high strength in conjunction with low density.   When compared to traditional lightweight refractories, these materials offer an impressive 200% more in cold crushing strength (CCS).   The castables increased strength does not affect its density, which is maintained at a noteworthy 80 pounds per cubic foot (pcf).   Product advantages also include:

• Excellent CCS and hot strength
• Great volume stability, low linear shrinkage
• Low density
• Great casting consistency
• Low thermal conductivity

Available Internationally As:  Plico® Castable LW 24 HS

Plibrico SDS Link – https://plibri.co/2XO3BoR

Product: Plicast LWI 28
Product #: 16009

Service Temperature Limit: 2800°F

Installation Method: Casting
Shelf Life: 9 months

Industries: Mineral Processing, Aluminum, Steel, Power Generation, Boilers, Incineration, Off-Gas, Refining

Best Applications: Functions and equipment requiring a very high temperature insulating component or reducing atmosphere resistant component. Typical applications include:

1. Fired heaters – radiant sections and roofs
2. Atmosphere heat treat furnaces and vessels
3. Incinerators and thermal oxidizers
4. Sulfur recovery units – back up insulation

Plibrico TDS Link – http://bit.ly/2ZiPBXS

Product Information: Plicast®️ LWI®️ 28 is a very high temperature insulating castable. A service limit of 2800°F and good strength make it suitable to use as either a backup insulating component in high temperature applications, or as a primary lining material in less severe applications. Its low iron content makes it ideal for use in reducing combustion applications. Product advantages include:

• 2800°F service limit
• Low iron content – <1%
• Medium density – ~85 pcf
• Good CCS and hot strength
• Moderately low thermal conductivity
• Good volume stability, positive linear change above 2500°F to its service limit
• Good casting consistency

Available Internationally As: Plico®️ Castable LW 28

Plibrico SDS Link – http://bit.ly/2zAi9Nj