Product: Pligun Fast Track 31 LCZ

Product #: 3324

Service Temperature Limit: 3100°F

Installation Method: Gunning

Shelf Life: 9 months

Industries: Boilers, Incineration, Off-Gas, Steel, Aluminum, Mineral Processing

Best Applications: This material is engineered to work well in a variety of industrial processes, these include:

  1. Fluidized Bed combustors
  2. Boilers – oil and coal fired
  3. Thermal Oxidizers – combustion and quench chambers
  4. Waste Incinerators – primary combustion chamber
  5. Aluminum furnaces – non-metal contact areas
  6. Mineral Processing Kilns – alumina, cement and aggregate calcining
  7. Steel/Ferrous – reheat/forge furnace, jambs, lintels, sills, roof and walls.

Plibrico TDS Linkhttps://plibri.co/45yvMKO

Product Information: Pligun® Fast Track 31 LCZ is a mullite based, low cement gun mix with 3% zirconia for strong slag resistance.   Engineered to be put into service more rapidly than traditional cement bonded gunning materials, cure times after installation can be reduced to 4 hrs, however for ideal physical characteristics 8 hrs is recommended.   After curing, initial heating can be as fast as 100°F/hr with no temperature holds.   Please refer to Plibrico Bake Out Schedule FT for specifics. Product advantages include:

  • Superior resistance to alkali attack and slags
  • High strength – both hot and cold
  • Strong abrasion resistance
  • Good Volume stability
  • Nice gunnablity

Available Internationally As: Plico® Gun Mix Fast Track 31 LCZ

Plibrico SDS Linkhttps://plibri.co/3zbd3Jk

Product: Pligun Fast Track SiC 80 TM

Product #: 3306

Service Temperature Limit:  2700°F

Installation Method:  Gunning, Hand Packing, Troweling

Shelf Life: 9 months

Industries: Power Generation, Waste-to-Energy, Incineration, Boilers

Best Applications:  Engineered for operations that require high refractory thermal conductivity.   Typical applications include initial installation and maintenance:

  1. Water wall studded tube protection in waste incinerators and boilers
  2. Applications requiring a high conductivity refractory

Plibrico TDS Link – https://plibri.co/3K8wzHV

Product Information: Pligun® Fast Track SiC 80 TM is an 80% silicon carbide gun mix.   This versatile product exhibits good gunning characteristics and is also designed for micro applications.   You can apply via hand packing or troweling for small applications and tight areas like behind boiler tubes and studs.    This material may be dried out / heated on an accelerated schedule and minimum cure time.   Cure times can be reduced to 4 hours!   However, for ideal physical characteristics a longer cure time is recommended.   Product advantages include:

  • Good mechanical strength
  • High thermal conductivity
  • Resistance to acid slag corrosion
  • Can be installed by hand packing or troweling
  • Fast Fire: Shortened bake-out schedule
  • Versatile material that can be installed with multiple methods

Available Internationally As: Plico Gun Mix Fast Track SiC 80 TM

Plibrico SDS Link – https://plibri.co/3PQubH3

Product: Pligun Fast Track SiC HP8

Product #: 3307

Service Temperature Limit:  2700°F

Installation Method:  Gunning

Shelf Life: 9 months

Industries: Power Generation, Waste-to-Energy, Incineration, Boilers

Best Applications:  Engineered for operations that require high refractory thermal conductivity.   Typical applications include:

  1. Initial Installation
    • Water wall studded tube protection in waste incinerators
    • Water wall studded tube protection in boilers
  2. Gunning Maintenance
    • Water wall studded tube protection in waste incinerators
    • Water wall studded tube protection in boilers
  3. Any other application requiring a high conductivity refractory

Plibrico TDS Link – https://plibri.co/3dF8EDC

Product Information: Pligun® Fast Track SiC HP8 is an 80% silicon carbide, high performance gun mix.   This product was developed to meet the demanding specifications for waste incineration boiler tube sheet refractory.   Independently evaluated against other competitive materials, Pligun Fast Track SiC HP8 achieved and excelled in many areas.   This material may be dried out / heated on an accelerated schedule and minimum cure time.   Cure times can be reduced to 4 hours!   However, for ideal physical characteristics a longer cure time is recommended.   Product advantages include:

  • High mechanical strength – both hot and cold
  • High thermal conductivity
  • Relatively low abrasion loss
  • Resistance to acid slag corrosion
  • Good gunability and low rebound
  • Capable of rapid start-up using accelerated dry-outs

Available Internationally As: Plico Gun Mix Fast Track SiC HP8

Plibrico SDS Link – https://plibri.co/3A9yIyf

Product: Pligun Fast Track 50

Product #: 3259

Service Temperature Limit: 3000°F

Installation Method:  Gunning

Shelf Life:  9 months

Industries:  Mineral Processing, Power Generation, Boilers, Incineration, Steel

Best Applications:  Engineered for general purpose and repair applications in industrial thermal processing industries, these include:

  1. Reheat, forging, and heat treat furnaces
  2. Incinerators and thermal oxidizers
  3. Fluidized bed combustors/boilers
  4. Utility boilers
  5. Dryers and calciners
  6. Stacks and ducts
  7. Gypsum kettles
  8. Crematories

Plibrico TDS Link – http://plibri.co/pligun-ft50

Product Information: Pligun® Fast Track 50 is a flint based super duty, high purity cement gun mix.   This low cement material may be dried out / heated on an accelerated schedule and minimum cure time.   Cure times can be reduced to 4 hours!   However, for ideal physical characteristics a longer cure time is recommended.   After curing, heat can be as fast as 100°F/hr with no temperature hold – refer to Plibrico Bake Out Schedule FT for specifics.   Product advantages include:

  • Economical, general purpose repair material
  • Very good density
  • Good for hot gunning
  • Good adherence to worn refractory
  • Good strength and volume stability
  • Better properties than a typical high cement gun mix
  • Very good gunability and low rebound
  • Capable of rapid start-up using accelerated dry-outs

Available Internationally As:  Plico® Gun Mix Fast Track 50

Plibrico SDS Link – https://plibri.co/33uzbfs

Product: Pligun Fast Track 80-31 Al

Product #: 3255

Service Temperature Limit: 

Aluminum Contact –  1700°F

Non-Contact – 3100°F

Installation Method:  Gunning

Shelf Life: 9 months

Industries: Aluminum

Best Applications: Engineered for hot and cold gunning maintenance, including:

  1. Aluminum melting and holding furnaces lower walls
  2. Aluminum melting and holding furnaces upper walls
  3. Stack melter hot wall repairs
  4. Jambs

Plibrico TDS Link – https://plibri.co/3ECuctJ

Product Information: Pligun® Fast Track™ 80-31 Al is a bauxite based, low cement gun mix engineered for demanding aluminum contact applications using Plibrico’s Al-Tuff technology.   Engineered to be put into service more rapidly than traditional cement bonded gunning material, cure times after installation can be reduced to 4 hrs, however for ideal physical characteristics 8 hrs is recommended.   This material has excellent gunning characteristics and can be gunned both hot and cold.   Product advantages include:

  • Good aluminum reaction/wetting resistance to 1700°F
  • Excellent gunning characteristics both hot and cold
    • Good water range
    • Reduced rebound
    • Good adherence/bonding
  • Good hot strength

 Available Internationally As: Plico® Gun Mix Fast Track 80-31 Al

Plibrico SDS Link – https://plibri.co/3CrZf9C

Product: Pligun Fast Track 31 LC

Product #: 13608

Service Temperature Limit: 3100°F

Installation Method: Gunning

Shelf Life: 9 months

Industries: Boilers, Incineration, Off-Gas, Steel, Aluminum, Mineral Processing

Best Applications: This material works well in many industrial processes, for a wide range of applications including:

  1. Fluidized Bed combustors
  2. Boilers – oil and coal fired
  3. Thermal Oxidizers – combustion and quench chambers
  4. Waste Incinerators – primary combustion chamber
  5. Aluminum furnaces – non-metal contact areas
  6. Mineral Processing Kilns – alumina, cement and aggregate calcining
  7. Steel/Ferrous – reheat/forge furnace, jambs, lintels, sills, roof and walls.

Plibrico TDS Linkhttps://plibri.co/3bjVTaF

Product Information: Pligun® Fast Track 31 LC is a mullite based, low cement gun mix engineered to be put into service more rapidly than traditional cement bonded gunning material. Cure times after installation can be reduced to 4 hrs, however for ideal physical characteristics 8 hrs is recommended. After curing, initial heating can be as fast as 100°F/hr with no temperature holds. Please refer to Plibrico Bake Out Schedule FT for specifics. Other product characteristics include:

  • High strength – both hot and cold
  • Good abrasion resistance
  • Volume stability
  • Good resistance to alkali attack and slags
  • Good gunnablity

Available Internationally As: Plico® Gun Mix Fast Track 31 LC

Plibrico SDS Linkhttps://plibri.co/2zv3OEM

  • Plibrico® Plastic Refractories

    Clay/Air Bond

    Product Name%Al2O3Service LimitSDS
    Plibrico®Super F AB58%2900F / 1590CSDS
    Plibrico®60 AB58%3100F / 1705CSDS
    Plibrico®80 AB78%3200F / 1760CSDS
    Plibrico®90 AB90%3400F / 1871CSDS

    Phosphate Bond

    Product Name%Al2O3Service LimitSDS
    Plibrico®55 S54%3000F / 1648CSDS
    Plibrico®68 S68%3100F / 1705CSDS
    Plibrico®68 SA68%3100F / 1705CSDS
    Plibrico®85 S Special83%3300F / 1815CSDS
    Plibrico®90 S90%3400F / 1870CSDS
    Plibrico®SiC 80(80% SiC)2700F / 1480CSDS

    (fine grain – soft)

    Product Name%Al2O3Service LimitSDS
    Plibrico®SR 6868%3100F / 1705CSDS
    Plibrico®SR 8583%3300F / 1815CSDS
    Plibrico®SR 9088%3400F / 1870CSDS

    Plibrico HyRATE® Plastic Refractories – Gunning Grade

    Clay/Air Bond

    Product Name%Al2O3Service LimitSDS
    Plibrico HyRATE®Super F AB43%2900F / 1595CSDS
    Plibrico HyRATE®60 AB60%3100F / 1705CSDS
    Plibrico HyRATE®80 AB78%3200F / 1760CSDS

    Phosphate Bond

    Product Name%Al2O3Service LimitSDS
    Plibrico HyRATE®68 S68%3100F / 1705CSDS
    Plibrico HyRATE®85 S Special84%3300F / 1815CSDS